Tank mix glyphosate for pre-seed burnoff

May 4, 2016 - Issue 7

Perennials and winter annuals are growing strong and some annuals are starting to show up. In those situations, growers often see a clear economic benefit from a pre-seed burnoff. This stops weeds from taking up moisture and nutrients right away, even if the crop isn’t seeded for a week or two.

Weeds_spring_Epp_600

If weeds are large, a rate of glyphosate up to 1.5 litres per acre (540 gram equivalent) may be required. A tank mix with glyphosate is also usually recommended.

Products approved for use ahead of canola are:

  • glyphosate
  • bromoxynil in a tank mix with glyphosate
  • Aim (carfentrazone) in a tank mix with glyphosate
  • CleanStart (carfentrazone and glyphosate)
  • clomazone in a tank mix with glyphosate
  • Conquer (bromoxynil and carfentrazone) in a tank mix with glyphosate
  • quinclorac

Bromoxynil has been shown to have better activity on volunteer canola than carfentrazone, but legume species (like black medic) will tolerate bromoxynil alone, so carfentrazone is better on these weeds. The combination of bromoxynil and carfentrazone is quite complimentary and generally gives better overall control than either alone. For more on this, see the section below “Conquer or CleanStart?”

With the discovery of glyphosate-resistant kochia in all provinces on the Prairies, it is important to apply glyphosate with a tank mix partner on this weed especially. Exceptions are in-crop on glyphosate-tolerant canola where no tank mix options exist.

Water volumes. Glyphosate is systemic, and can be effective at lower water volumes and coarse to extra coarse spray qualities. Carfentrazone and bromoxynil are contact and benefit from higher water volumes and medium to coarse spray qualities. Nozzle manufacturers publish the spray qualities of their nozzles in their catalogues and apps.

When mixing with glyphosate, consider the efficacy of the tank mix partner when setting water rates and droplet size. After all, if the tank mix partner wasn’t important, you would use straight glyphosate.

Use at least 5 gal/ac and closer to 10 for improved efficacy. One way to move droplet size from very coarse to coarse or medium with the same nozzles is to increase ground speed. By doing so, the rate controller will increase pressure which will reduce droplet size and may improve performance of contact product.

Water quality. Hard water tends to reduce glyphosate performance, especially at higher water rates. When tank mixing with glyphosate and increasing water volume, it is important to consider water quality. Send water to a testing lab. If “total hardness” is below 350 ppm (or 20 “grains”), the water source is good as is. For harder water, a conditioner such as spray-grade ammonium sulphate can be added to negate the effect of hard water cations.

Spraying in cold weather. Applications of glyphosate and many other herbicides made in cold conditions often result in poor weed control. For example, cloudy days with highs of 10°C after a night near 0°C will often result in poor herbicide performance. Biological activity would have stopped when temperatures drop below 5°C and would not start up again until the plant warmed to at least 5°C — and even then it would be very slow. No biological activity means no herbicide activity.

Ideally glyphosate applications will be made:
—When temperatures are greater than 10°C, with the expectation that daytime highs will increase to greater than 15°C
—When nighttime lows are greater than 5°C (the warmer the better up to 10°C)
—Under bright sunshine (thin or sporadic clouds are also OK). Applications made in darkness or heavy cloud are less effective.

How long to wait to seed after spraying?
Glyphosate only: For annuals and winter annuals, glyphosate needs only 24 hours to get to the growing point. After a day, the crop can be seeded. For perennial weeds, 3 days should be enough in sunny and warm conditions but 5 days is recommended before seeding if weather is cloudy or cool.
Contact herbicides: Generally the activity of contact herbicides such as bromoxynil and carfentrazone is very quick (within hours), so seeding the following day is appropriate. Contact herbicides for use prior to canola are not very effective on perennial weeds so leaving them for an extended period will not provide improved efficacy. Most contact herbicides are recommended to be mixed with glyphosate and those wait periods will be the most limiting in most cases.
*Slowing down and increasing water volumes will improve the performance and return on investment for the contact active ingredients (Groups 6 and 14).

Sprayer clean out. During the pre-seed weed control season, take care to thoroughly clean the sprayer on a regular basis to remove active ingredients that could damage crops when you go back to the fields in a few weeks for in-crop applications. A good rule of thumb is to clean the sprayer any time the power plant of the sprayer needs to be shut down. Pay extra attention to screens and boom ends where residue tends to sit. MORE

Conquer or CleanStart? To protect against selection pressure for herbicide resistance, the common practice is to use multiple modes of action. Conquer with glyphosate is a three-active solution (Groups 6, 9 and 14). CleanStart is a two-active solution (Groups 9 and 14.) Conquer provides faster, more complete control of glyphosate-tolerant volunteer canola, and better control of kochia, wild buckwheat, narrow-leaved hawks beard, cleavers and thistle. NuFarm, which provides both products, says “CleanStart is a simple one step solution to resistance and mproved weed control. Conquer provides a more sustainable solution with faster, more complete weed control in all situations.”

Further reading:

Control weeds early, save yield
PODCAST: 10 tips to manage cleavers
Pre-seed burnoff: 8 top weeds and how to control them

Canola Watch